Loading... Please wait...
  • CALL US ON 1-877-893-0313
  • My Account
  • Gift Certificates

Installing Car Seat Covers

How to Install an Infant Car Seat Cover

 

Graco Snugride and Safe Seat
Infant car seat cover and canopy slipcover instructions


Carseat Cover Replacement:

Please refer to your Graco handbook to unthread the straps on your infant car seat cover.

1. If you do not have your handbook then please follow these directions:

a.) In the back of the carseat, unlatch the seatbelts from the metal bracket
b.) Pull the loose seatbelts from the front, and they should slip right out of the seat

2. Once you have pulled the seatbelts loose slip your Ritzy Baby Cover over the top of the existing cover and repeat the process in reverse, making sure all seatbelts are placed in the correct places and secured in the back with the metal bracket.

Canopy Replacement:

1. Push the Graco canopy to one side, exposing the plastic support bars that hold the canopy in place.

2. The center of the support is where the canopy comes apart. Using both hands, pull the canopy support bar apart (as if you were playing tug-of-war).

3. Once the support bars are apart, remove the old Graco canopy and slip on the Ritzy Baby Cover Canopy.

4. Secure the support bars by snapping them shut, and then slide the canopy into place.

If you have any difficulty, please contact us.

 

Britax- Companion
2005, 2006, 2007,2008
Infant seat
Britax Infant Companion – Slipcover Car Seat and Canopy Instructions


Car seat Cover Replacement:

1. Do not remove original Britax cover from car seat. Your Ritzy Baby cover is made to be used as a slipcover only. Instructions on how to unthread your seat belts can be found in your original handbook.

If you do not have your Britax handbook then please follow these directions:

a.) In the back of the car seat, unlatch the seat belts from the metal bracket
b.) Pull the loose seat belts from the front, and they should slip right out of the seat
c.) Once the seat belts are out of the original Britax cover, slip your Ritzy Baby cover over the top of the existing car seat cover.

2. Once you have your slipcover on then repeat the seat belt process in reverse, making sure all seat belts are placed in the correct places and secured in the back with the metal bracket.

Canopy Replacement:

1. Push the Britax canopy to one side, exposing the plastic support bars that hold the canopy in place.

2. The center of the support is where the canopy comes apart. Using both hands, pull the canopy support bar apart (as if you were playing tug-of-war).

3. Once the support bars are apart, remove the old Britax canopy and slip on the Ritzy Cover Canopy.

4. Secure the support bars by snapping them shut, and then slide the canopy into place (do this for both the front and back support bars).

 

Peg-Perego Primo Viaggio 2002-2005
Peg-Perego Primo Viaggio (2002-2005) – Car Seat and Canopy Instructions


CarSeat Slipcover Installation:

1. Do Not Remove original Viaggio cover from carseat. Instructions on how to unthread your seat belts can be found in your car seat manual. handbook.

If you do not have your Viaggio handbook then please follow these directions:

a.) In the back of the carseat, unlatch the seatbelts from the metal bracket
b.) Pull the loose seatbelts from the front, and they should slip right out of the seat
c.) Once the seatbelts and lower 5 point buckle (located in the lower portion of carseat in between the babies legs) are out of the original Viaggio cover, slip your Ritzy Cover over the top of the original car seat cover and repeat the seatbelt process in reverse, making sure all seatbelts are placed in the correct places and secured in the back with the metal bracket.

Canopy Replacement:

1. Detach the whole canopy from the carseat.

2. You should have in your hands the whole original canopy with support bar.

3. Slide original canopy slightly to one side, exposing the support bar that clicks into the plastic bracket (you will see where the bar attaches to the circular plastic bracket).

4. Where the bar slides into the circular plastic bracket, take a very large, standard (flat) head screwdriver. Slide the flat end up under the space between the bar and bracket, and lift the bracket high enough to slide the bar out from under it (pulling gently on the bar while lifting the bracket).

5. Slide off the original Viaggio canopy and slip on the Ritzy Cover Canopy.

6. Snap the bar back into the Viaggio bracket and adjust Ritzy Cover Canopy.

7. Reattach canopy to carseat.

 

Peg-Perego Primo Viaggio 2006 and 2007 SIP and 2008 SIP 30/30–
Car Seat Slipcover and Canopy Instructions


Carseat Slipcover:

1. Do not Remove original Viaggio cover from carseat. Instructions on how to unthread the seatbelts can be found in your original handbook.

If you do not have your Viaggio handbook then please follow these directions:

a.) First you will need to remove the attached headrest. Carefully slip the bottom of the headrest off of the plastic support piece – Caution: Be very gentle or else you can crack the Styrofoam insert – and then lift up the headrest cover so that you can remove the lower Styrofoam padding. Set the Styrofoam padding aside. Lift the headrest cover high enough to see the two screws that attach the headrest to the carseat. Using a Phillips head screwdriver, remove both and set them aside. Now you can remove the headrest from the body of the carseat, this will allow you to unlatch the seatbelts.
b.) In the back of the carseat, unlatch the seatbelts from the metal bracket
c.) Pull the loose seatbelts from the front, and they should slip right out of the seat
d.) Once the seatbelts are out of the original Viaggio cover, slip your Ritzy Cover over the top of your Viaggio cover.

2. Once you have placed your Ritzy Cover over the top of your original Viaggio cover then repeat the process in reverse, making sure all seatbelts are placed in the correct places and secured in the back with the metal bracket.

Headrest:

DO NOT REMOVE ANYTHING of the headrest. Reattach the headrest to the body of the carseat and screw the 2 screws back in nice and tight; insert the lower Styrofoam into the headrest and you are done.

Canopy Replacement:

1. Detach the whole canopy from the carseat.

2. You should have in your hands the whole original canopy with support bar.

3. Slide off the original Viaggio canopy and slip on the Ritzy Cover Canopy

4. Adjust Ritzy Cover Canopy. Reattach canopy to carseat.


 

Recent Updates

Connect with us

Newsletter